Lightcounting Two Sides Of The Market – Two Different

Browse technical resources about fiber optic infrastructure, FTTH, PON, campus and carrier networks.

  • Interconnection between different VLANs on the core switch

    Interconnection between different VLANs on the core switch

    In order to establish inter-VLAN communication (i. e routing between hosts belonging to different VLANs) you need to have a Layer 3 routing engine in the network. Virtual Local Area Network (VLAN) helps break a large network into smaller, manageable parts, improving security and efficiency. Instead of buying five physical switches for five departments, you buy one switch and create five VLANs. Multilayer switches can forward frames based on MAC address information and can also forward IP packets based on IP. Inter-VLAN routing using the router-on-a-stick method is simple to implement for a small- to medium-sized organization. Cisco NX-OS (Nexus Operating System) is the software which is powering this new generation of switches and has many similarities (regarding command structure etc) with the traditional IOS software which has been in production for decades. I have prepared this article to showcase a simple yet.

    [PDF Version]
  • The IP addresses of the switch and the access network are different

    The IP addresses of the switch and the access network are different

    As you point out, switches operate at layer 2 (MAC level) so IP addresses and subnets mean nothing to them. If your switches are connected to different interfaces on your router, then they are usually on different subnets, but that configuration is done on the. Not every switch or AP comes equipped with an IP address: Unmanaged Switches: These basic switches operate without configuration interfaces and do not possess IP addresses. They work transparently, forwarding data without any need for IP identification. This white paper introduces the following three types of network switches and further discusses the selection criteria for each switch. If there comes a situation where I need to know the IP addresses of the devices connected to either Switch A or B, what would be the right way to find it? I know that if I run the command Show Arp, it would display the. The Switch is a network device that is used to segment the networks into different subnetworks called subnets or LAN segments. A switch operates within a single VLAN and broadcast domain, which matches one IP subnet.

    [PDF Version]
  • What are the different splicing methods for dual-film optical cables

    What are the different splicing methods for dual-film optical cables

    Fiber optic splicing is often the preferred way to connect two fiber optic cables because it has lower light loss (attenuation) and back reflection than connectorization. Fusion splicing and mechanical splicing are the two most common methods of fiber optic splicing. For network managers and technicians, a poor splice can lead to significant signal degradation, network downtime, and costly troubleshooting. What is Fiber Optic Splicing and Why is it Needed? – #1.


  • What is the interface at the back of the fiber optic panel

    What is the interface at the back of the fiber optic panel

    A fiber-optic adapter — sometimes called a coupler or bulkhead coupler — is a passive mechanical interface that mates and aligns two terminated optical fibers (i., two fiber connectors) such that light can reliably pass from one to the other with minimal insertion loss and maximum. An optical fiber connector is a device used to link optical fibers, facilitating the efficient transmission of light signals. An optical fiber connector enables quicker connection and disconnection than splicing. The number of. Fiber optic patch panels are enclosures that act as a distribution hub for fiber cable. Most are roughly the diameter of a human hair, and.


  • Cable routing on both sides of the cable management rack

    Cable routing on both sides of the cable management rack

    Use the cable raceways on the sides of the rack to manage excess power cables. This routing helps to. Organizing cable management within a rack simplifies network device access and makes it easier to track cables during installation. This article introduces two types of cable managers—horizontal and vertical—detailing their features and providing guidance on proper installation within a rack. FS. There are lots of fantastic examples in r/cableporn on how to do this VERY WELL: This is a fantastic example of how to do service loops if you don't have cable tray or space above ceiling tile: If you are not sure how to make it look like this, get a cablecomb: Here are a few more of my choice. be isolated from data cables on opposite sides of the rack to reduce th ks will have varying lengths of cable resulting in the need to deal with excess cable. Within each layer of patch panels inside.

    [PDF Version]
  • What equipment is connected to the back of the cabinet

    What equipment is connected to the back of the cabinet

    The nailer strips are attached across the back of the cabinet where it meets the wall. Base cabinets should be attached at the studs in the wall to prevent them from shifting out of alignment or tipping forward when the drawers are opened. Knowing the parts of a cabinet and how they go together will take the mystery out of your remodel! Making your own cabinets sounds like a big, scary project, but if you can build a box, you can build a cabinet! It helps to know the terms for the various. The cabinet box forms the primary structure of a cabinet. It consists of several key components that provide strength, stability, and enclosure. By familiarizing yourself with these technical terms, you'll be better equipped to discuss cabinet issues. As with other parts of the house, let us enumerate the parts of the cabinet. Includes styles like shaker, raised panel, and flat.

    [PDF Version]

Fiber & Network Infrastructure Insights

Need Professional Fiber Optic & Network Solutions?

Contact us today for product inquiries, custom solutions, or technical support